0
Do you replace the coil from a 6 volt to a 12 volt when converting from 6 volt to a 12 volt system?
Wiki User
∙ 13y ago
Yes. Since the coil is run at full voltage when starting 12 volts may be too much for a 6 volt ignition coil. It would be at about 8 volts when running. There is a starting resistor.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is no volt coil?
no volt coils are used to de-energise a contactor should a situation arise in which voltage is zero
Why name no volt coil?
Following a power cut, it's important that motors aren't allowed to self-start when the power is restored, as that would represent a serious hazard. So, a no-volt coil is a part of a motor-control system that ensures, in the event of a power cut, the control system disconnects the motor so that it cannot self start.
Is the voltage for 1957 Chevy truck 6 volt or 12 volt?
From the factory it will have a 6 volt, positive ground system. However, it is popular to replace the original system with a modern 12v system.
1952 dodge truck is it a 12 volt system or 6 volt system?
The 1952 Dodge truck line used a 6 volt electical system with a generator.
How do you rewire a 110 volt HID Magnetic coil ballast to use 220 volt?
Unless the ballast is a multi tap primary you can not rewire it for 220 volts.
What happens if you use a 12 volt coil with a 6 volt system?
Probably not much because 6 Volts is not enough to power a 12 Volt coil
What is no volt coil?
no volt coils are used to de-energise a contactor should a situation arise in which voltage is zero
What is the number of turns in primary and secondary coil for 12 volt battery charger with 220 volt power supply?
what is the number of turns in the primary and secondary coil for 12 volt battery charger with 220 volt power supply> what is the number of turns in the primary and secondary coil for 12 volt battery charger with 220 volt power supply>
Why not no volt coil?
It is impossible to figure out the question.
Is the voltage for 1957 Chevy truck 6 volt or 12 volt?
From the factory it will have a 6 volt, positive ground system. However, it is popular to replace the original system with a modern 12v system.
Why name no volt coil?
Following a power cut, it's important that motors aren't allowed to self-start when the power is restored, as that would represent a serious hazard. So, a no-volt coil is a part of a motor-control system that ensures, in the event of a power cut, the control system disconnects the motor so that it cannot self start.
Can you jump a 24 volt system with a 12 volt system?
No
How you can pass electricity 20 volt and 25 amp from converting 12 volt 1 amp adopter to 20 volt and 25 amp?
A 1-amp adaptor can not be used for equipment that draws more than 1 amp. It is not clear from the question which part of your system is 12 v and which is 20 v.
What would be the result if a 24 volt 20-ohm low voltage contactor coil were wired in series with a 24 volt 200-ohm control relay coil?
Nine tenths of the voltage would appear across the 200-ohm coil.
Can you use a 6 volt relay to 230 volt circuit?
If you are talking about a 6 volt coil, yes, so long as the contacts are rated for the 230 volt circuit. If you are talking about 6 volt contacts, no, absolutely not.
Can a coil be made to fire not being on a car?
probably an old style 6 volt coil with an old-style 'lantern=battery' (6 volt) big fat square thing with the springs on top or old style 12 volt coil with like gas lawn mower key-start (completely sealed) battery /has male tabs/ on top. but coil will not hold a charge for later use.
1952 dodge truck is it a 12 volt system or 6 volt system?
The 1952 Dodge truck line used a 6 volt electical system with a generator.
