answersLogoWhite

0


Best Answer

Serpentine Belt

Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram.

If it is not you can run down to your nearest auto parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.

Relieve Serpentine Belt Tension.

Before removing the belt, note its routing around all applicable pulleys for ease of installation.

1. Using a box end wrench on the tensioner pulley center bolt, rotate the tensioner assembly clockwise.

2. While holding the tensioner in this position, remove the alternator drive belt from one or two of the applicable pulleys.

Use a box end wrench to rotate the tensioner pulley assembly clockwise to relieve serpentine belt tension

1. Slowly release the tensioner, and remove the box end wrench from the center bolt.

2. Remove the alternator drive belt from the remaining applicable pulleys.

To install:

When installing the drive belt on the pulleys, ensure that it is properly seated in all of the pulley grooves.

1. Using the box end wrench, rotate the tensioner clockwise again, then position the drive belt on all of the pulleys.

2. Slowly release the tensioner until it eliminates all drive belt slack.

3. Inspect the tensioner indicator to be sure that the belt is properly tensioned. If the belt tension is incorrect, the belt should be replaced with a new one, or, if installing a new belt, the belt may not be the correct belt for your vehicle.

4. Then start the engine. Ensure that the drive belt works properly.

5. Stop the engine, then double-check to ensure that the belt is properly seated on all applicable pulleys.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Diagram for a serpentine belt 1998 ford f-150?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is Serpentine belt routing diagram for 1990 Ford f150?

I need the routing for the serpentine belt for 1990 Ford 150?


Can you tighten a serpentine belt on a 1998 V8 ford f150 4x4 and how do you do it?

the belt tensioner does it by itself.short answer no


1992 ford f150 serpentine belt diagram?

its under your hood with the firing order and distributor order


Where can you find a serpentine diagram for a ford f150?

Do you mean a SCHEMATIC diagram?


Where is a serpentine belt routing diagram for a 1994 ford F150?

I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine I need a diagram for a serpentine belt for a 1994 f150 with 5.0 engine There should be a sticker near radiator shroud that has belt routing. If not stick the belt down past the right side of fan/water pump .put belt on crank pulley then pull back of belt over water pump and then down around power steering pulley and up over compressor pulley. put belt from crank pulley around smog pulley then up to tensioner with back of belt around tensioner and then around alternator pulley.next put rachet and socket(15 mm) on tensioner and pull on it while placing belt under idler pulley.


How do you relieve tension on the serpentine belt of a 1994 f150 5.0 and is a special tool needed?

Serpentine puller


How do you install a new fan belt on a 1998 Ford F150?

The serpentine belt has a tensioner that you nust pry up to remove the belt. There should be a schematic of the routing of the belt on the fan shroud. If not, draw one before removing it.


How do you replace an idler pulley on a 1997 Ford F150 5.4ltr?

Remove serpentine belt. Remove pulley. Install new pulley. Install serpentine belt.


Can you replace your serpentine belt on your 97 Ford F150 v-8 4x with ac to a standard serpentine belt for a Ford F150 without ac as you feel the ac compressor is shot?

yes,a good parts man will give you a belt to bypass your ac.


Where can you get a diagram of the belt installation on an F150?

I have a 1998 Ford F-150 V6. The diagrahm is on the fan shroud. Open the hood and take a look if its a newer model.


How do you change a serpentine belt on a 97 F150 Ford?

Serpentine Belt Under the hood should be a diagram of the belt, this is your best reference without the service manual. All you have to determine is which direction to rotate the belt tensioner, and then put the belt back on as shown in the diagram. If it is not you can run down to your nearest auto parts store and they can print it out for you or just buy the Hayes or chilton manual on your car. It only cost a few bucks and it well helps you out later down the line if something else brakes.


Vacuum Diagram For A 1998 Ford F150?

The vacuum diagram for a 1998 Ford F150 is located in the service manual. It details how each vacuum line is routed, where the line is attached, and its function.