0
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Wiki User
∙ 12y agoDefinitely NOT. You get 110 V between one of the two hot 220 V conductors and neutral. Voltage between neutral and ground should be zero.
Add your answer:
Earn +20 pts
How do you tap into a 220v feed going to baseboard heater and get a 110v supply?
This is only valid in parts of the work using 110/220 Volt split phase power system. There will be 110V from each of the hot leads to ground/neutral, so connect your outlet to only one of the hot leads, the neutral lead and the earth ground lead. This may be a problem with a dedicated 220V circuit as there will likely be no neutral line. Another note - this could well cause an unbalanced electrical load across the two pole breaker. If the breaker has a rating of 20A and the 110V circuit draws much of that current, the heater will likely trip the breaker.
How do I get 220 volt circuit?
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
How do you run a clothes dryer line to a fuse box that has glass fuses if there are 2 in the box that are not being used?
You need a 220V cartridge fuse block open, not just two 110V fuses. Fusing a 220V device with two 110V fuses at the panel is dangerous and doesn't meet code. If you have a 220V fuse block open, simply wire the two hots to the block, and then wire the neutral and ground normally. If you have fuses make sure the box and the feed can handle a clothes dryer. It may be wise to have an electrician evaluate the system for safety.
Can I use a 220V oven with 110V outlet?
No, and if you don't have a 220v outlet, you will need an electrician to run a #8 copper wire with a direct line to the electrical panel (40 or 50 amp), depending on the oven's requirments - check the manual.
How do you add an extra 220v outlet to a 220v line?
Typically you need 4 conductors. The hot wires are usually red and black. The neutral is white and the ground is green. If you put a volt meter across red and black you'll get 220 VAC. If between neutral and either hot 110 VAC.
How do you tap into a 220v feed going to baseboard heater and get a 110v supply?
This is only valid in parts of the work using 110/220 Volt split phase power system. There will be 110V from each of the hot leads to ground/neutral, so connect your outlet to only one of the hot leads, the neutral lead and the earth ground lead. This may be a problem with a dedicated 220V circuit as there will likely be no neutral line. Another note - this could well cause an unbalanced electrical load across the two pole breaker. If the breaker has a rating of 20A and the 110V circuit draws much of that current, the heater will likely trip the breaker.
An electric iron always draws a current of 3.4 amp from the 220v supply line what current will this electric iron draws when connected to 110v supply line?
1.7amp
How do I get 220 volt circuit?
If you need a 220v circuit at only 15 or 20 amps: Get a new breaker to replace your 110v single pole breaker with a 220v double pole breaker. (You cannot exceed the original breaker's amperage rating unless you also replace the wire with a larger size). Shut off the panel's main breaker (the wires coming into the main breaker will remain hot, so don't touch them.) Remove the old 110v circuit's neutral (white) from the neutral bus bar in your distribution panel. Remove the old 110v circuit's hot (black) from the old 110v breaker. Remove the old 110v breaker. Install the new 220v breaker in place of the old breaker. (This may require you to rearrange some breakers if the old breaker was in between others) Reconnect the black wire to one terminal of the 220v breaker, and reconnect the white wire to the other terminal. Turn on the main breaker, and your new 220v breaker. Before you do this, be sure where the actual circuit goes. Changing 110v to 220v if the circuit is feeding regular 110v receptacles will cause damage to devices plugged into them. Be sure you remove all 110v devices (receptacles) from the circuit before converting it. If you need a 220v circuit for a dryer or other large appliance, your existing wiring will not be sufficient to do the above. You will need to install a new breaker and wiring. For this task, you should consult a professional electrician.
How do you run a clothes dryer line to a fuse box that has glass fuses if there are 2 in the box that are not being used?
You need a 220V cartridge fuse block open, not just two 110V fuses. Fusing a 220V device with two 110V fuses at the panel is dangerous and doesn't meet code. If you have a 220V fuse block open, simply wire the two hots to the block, and then wire the neutral and ground normally. If you have fuses make sure the box and the feed can handle a clothes dryer. It may be wise to have an electrician evaluate the system for safety.
Can I use a 220V oven with 110V outlet?
No, and if you don't have a 220v outlet, you will need an electrician to run a #8 copper wire with a direct line to the electrical panel (40 or 50 amp), depending on the oven's requirments - check the manual.
How do you wire a 220v three prong to a 220v four prong?
You'll need to contact an electrician who will pull a new wire for you. If you only have 2 wires on the 240 line, you don't have a neutral or a ground; both of which are essential for a modern electric range.
How do you add an extra 220v outlet to a 220v line?
Typically you need 4 conductors. The hot wires are usually red and black. The neutral is white and the ground is green. If you put a volt meter across red and black you'll get 220 VAC. If between neutral and either hot 110 VAC.
Can you properly change a 3-prong 240V outlet looks like standard plug but horizontal to the NEMA twistlock 20A style if they use a different number of wires extra ground neutral on a twistlock type?
No. You can't replace a 220V outlet with a 110/220V outlet without running the requisite neutral wire. If you do you will blow out any device that expects the neutral line to be connected.
How would you make a patch cord to go from a 220V 30-amp 4-wire generator to run a 220V 20-amp 3-wire portable compressor?
Identify the neutral wire on the generator. This will be the unused conductor to run the compressor. The ground and line1, line 2 are all that are needed.
Is 220V line voltage or phase voltage?
Phase, if you are referring to line, as power line from pole.
Can you plug two appliances a 120v and a 110v on the same line which is a 110v?
Should be ok provided you do not draw too much current.
What should be the primisable voltage between neutral and earth in a three phase system?
It is the line to line voltage divided by 1.73. 600V / 1.73 = 347V 480V / 1.73 = 277V 380V / 1.73 = 220V 208V / 1.73 = 120V
