answersLogoWhite

0


Best Answer

Just finished engine rebuild on 2.5 tdi acv engine. Couldnt find a timing mark ANYWHERE. But...... inside the bell houseing, there is a notch!. Get it roughly to TDC, then as you turn the wheel the notch is to the left of the teeth. You have to get your head right in the engine bay on the right hand side and look towards the the arrow shaped ally on the casing. The notch will only be visible either side of the arrow shape as it hide behinds it when in correct position. What a mission to find it and i still couldnt be sure it was right until we ran the engine and it was. Good luck!!!!

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Cam timing mark on vw 2.5 tdi transporter acv engine?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you line up the timing marks on a 3406E Cat engine.?

pin the engine on the flywheel. line the timing mark on the cam gear with the timing mark located on the timing cover. the mark on the cover is located at the top and is just a bump formed in the cover.


What does the cam sprocket line up with when putting on a timing chain?

Generally, for most single cam engines, there is a dot or mark on the cam sprocket and a similar mark on the crank sprocket. Point them at each other. the timing marks on the crank and cam sprockets must be lined up with marks on the timing chain in an overhead cam engine


Which timing mark do you use to set timing belt on a 1998 metro cam sprocket has two marks. engine is 1.3 liter?

On my 2000 Metro with a 1.3L the mark and slot marked with the "E" are used.


Where are the timing marks for 1990 Mazda MPV 3.0?

the right gear cam go to the center of the engine and the left go to the center of the engine like croos eyes o .-.o and the cam gear it have the mark it go to top point it to the mark on top


Where should the timing mark on the cam gear and the timing mark on the crank gear be to be in time on a small block Chevy engine if number 1 cylinder is at top dead center on the compresson stroke?

The cam gear is on top/ and the crank gear is on top. Both at 12:00.


How can you get the timing mark matched up with the cam and crank shaft on a 305 vortec Chevy engine when the engine is all put together and running so i can get the timing between -2 and plus 2?

That requires an OBDII engine scanner to do that.


How do you set cam timing on a 4.6 SOHC?

The cam timing on a 4.6 SOHC engine is set by aligning the timing marks of the timing chain to the cam sprocket. This sets the initial timing based on factory settings.


What is the timing specification for Mitsubishi 4M51 engine?

what is the cam timing specification for mitsubishi 4M51 engine?


How do you set ignition timing on a 1996 2.2 liter engine?

align the crankshaft pulley mark with mark on oil pump housing, and align marks on cam gears with marks on rear cover, then install timing belt.


What is a cam sprocket?

A cam sprocket is a part which is attached to one end of a cam shaft in an engine. A cam sprocket, along with the timing belt maintain the timing between the camshaft and crankshaft, which ensures that the engine runs properly.


What positions should the intake cam lobe be at top dead center when installing the top chain?

HOW DO YOU GET THE IDLER PULLER TO THE PRPOER MARK? WHEN INSTALLING THE TOP TIMING CHAIN ; THE TIMING MARK ON THE IDELER PULLEY FOR THE TOP CHAIN, TO ALIGN THE CAM SPROCKETS? HOW DO YOU GET THE IDLER PULLER TO THE PRPOER MARK? WHEN INSTALLING THE TOP TIMING CHAIN ; THE TIMING MARK ON THE IDELER PULLEY FOR THE TOP CHAIN, TO ALIGN THE CAM SPROCKETS?


How do you set the cam timing on a Honda xr80?

Point the intake cam lobe down and the timing mark on the cam gear at the 12 o clock position with the piston at TDC.